Products
∰ Boiler
Water Treatment ∰
|
Code |
Name &
Description |
|
Boiler Treatment Ideal to remove not only calcium carbonate & calcium
phosphate deposits but also calcium sulfate and barium sulfate as well.
Highly concentrated alkaline product. Eliminates excessive precipitation of
solids and reduces sludge accumulation. Application For
use with pre-softened make-up water and effectively disperses iron oxides as
well as calcium phosphate and clay. Injected directly into the boiler by
means of a proportioning pump. On-line descaler for boiler. It is environmentally safe, non-hazardous
and non-corrosive. Dosage Initiai: 2 quarts per 1,000 gallons or 2 : 4,000
Maintenance:1 quart for every 1,000 gallons of make-up water or 1 : 4,000 Maintain 15-25 ppm (mg/l) of orthophosphate in the boiler
water. Continue this program for 3 month period, then wash out. If result are
minimal, double the next six month operating period |
|
|
Sludge Conditioner LC 101 is used in steam boiler systems where water is zeolite softened
or in natural waters very low in hardness. This treatment will prevent scale
formation from residual hardness in addition to conditioning sludge. LC 101
is a balanced blend of polymers, which are mildly alkaline scale and
corrosion inhibitors in addition to sodium sulfite for added pitting and
corrosion protection. If 20 to 30 ppm (mg/l) of sulfite cannot be maintained
with a normal dosage of LC 101, add LC 102 to hold this recommended level. Application Easily fed to the boiler as a slug dosage
or by chemical proportioning pump directly into the boiler. It can also be
injected into the feedwater tank. Formula LC 101 contains no heavy metals. Dosage Initial dosage is one (1) quart per 1,000 gallons and
one (1) quart thereafter for every 800 gallons of make-up water. Maintain
20-3- ppm (mg/l) of orthophosphate in the boiler. |
|
|
Oxygen Scavenger Catalyzed
Oxygen Scavenger with Polymers for preventing pitting. Ideal for use with
both hard and pre-softened make-up water. Application Can be injected directly into the
boiler by means of a proportioning pump. Advisable to gradually feed LC 102
by means of a chemicals proportioning pump into the storage section of the
de-aerating heater as far ahead of the boiler as possible to provide maximum
effectiveness in high pressure boiler operating from 100-600 psi. or where
large amount of water is used. Dosage Initial: 3 quarts per 1,000 gallons or 3 : 4000 Maintenance: 1 quart for every 1,000 gallons of make-up
water or 1 : 4000 Maintain 20-50 ppm (mg/l) in
the boiler water. LC 102 can be used in conjunction with other formula in our
product line, but should not be used in a boiler operating in excess of 600
psi. Ù
|
|
|
On-line Boiler Descaler LC 103 is a very concentrated alkaline product used in boilers with
pre-softened make-up water primarily for the purpose of removing stubborn existing
scale. It is a very highly concentrated bled of polymers and phosphonates
designed specifically to breakdown old calcium and magnesium carbonate scale
deposits safely. LC 103 while reducing existing scale deposits eliminates
excessive precipitation of solids thereby reducing sludge accumulation. Application Injected directly into the boiler by
means of a proportioning pump. This product, in addition to its being
environmentally safe, is easily handled since it is non-hazardous and non
corrosive. Dosage Initial dosage is two
(2) quart per 1,000 gallons and thereafter approximately one (1) quart for
every 1,000 gallons of make-up water. Maintain 15-25 ppm (mg/l) of
orthophosphate in the boiler water. Ù
|
|
|
Boiler Internal Treatment LC
105 is an ideal one product boiler internal treatment. It can control not
only calcium carbonate & calcium phosphate deposits but also calcium
sulfate and barium sulfate. Highly concentrated alkaline product. Eliminates
excessive precipitation of solids and reduces sludge accumulation. Application For use with make-up water with
hardness below 150 ppm. and effectively disperses iron oxides as well as
calcium phosphate and clay. Injected directly into the boiler by means of a proportioning
pump. It is environmentally safe, non-hazardous and non-corrosive. Dosage Initial: 2 quarts per 100 gallons or 1 : 200 Maintenance: 1 quart for every 100 gallons of make-up
water or 1 : 400 Maintain
15-25 ppm (mg/l) of orthophosphate in the boiler water with pH within 11.0 –
12.0 in the boiler waters. Maintain cycle of concentration below 3000 ppm.
Consult LifeChem Technical Services when hardness is low or high. Ù
|
|
|
Steam Line Boiler Treatment LC
106 is an ideal steam line anti corrosion treatment for boilers. It is a
highly concentrated, alkaline product. Eliminates corrosion in the outgoing
steam lines and stabilizes pH in the condensate. Application For use with boilers which requires anti-corrosion
treatment in the steam lines. It disperses with steam and forms a protection
film on the inert surfaces of the steam pipes. Injected directly into the
boiler by means of a proportioning pump. It is environmentally safe. DO NOT
USE IN BOILERS WHERE STEAM CONTACTS FOOD. Dosage Initial: 1 quarts per 100 gallons or 1 : 400 Maintenance: 1 quart for every 200 gallons of make-up
water or 1 : 800 Maintain pH of 7.5 –
8.5 in the steam line of system. Maintain sulfite of 30 – 60 ppm along with LC
106. Maintain the cycle of concentration ( CoC ) less than 3000 ppm. Ù
|
|
|
Threshold Treatment For Boiler & Feed Water
Lines LC 107 prevents scale formation in feed water lines to
the boiler where hard water is used as make-up water. It is a balance blend
of sequestering agent which is mildly acid. It is a liquid product which must
be administered gradually to the feed water tank by means of a chemical
proportioning pump. It contains no heavy metals. Application Injected directly into the boiler by means of
a proportioning pump. This product, in addition to its being environmentally
safe, is easily handled since it is non-hazardous and non corrosive. Dosage No initial dosage need
to be applied to the boiler or feed water tank. The maintenance dosage is
adjusted by means of a chemical pump to provide orthophosphate levels between
20 to 30 ppm (mg/l) in the boiler water. Maintain 2-3 ppm in the make-up
water by using approximately 1 quart per 1,000 gallons. Ù
|
∰ Cooling
Tower Water Treatment
∰
|
Code |
Name & Description |
|
Cooling Tower Treatment For Soft Make-up Water LC 120 is a product which effectively prevents scale
and corrosion in cooling towers having very soft waters which are more
corrosive, have a Rysnar Index over 7 and calcium 25-75 ppm in the make-up
water. It is an excellent dispersant for calcium phosphate, iron oxides and
clay. This product is used where heavy metals and zinc is not allowed in
effluent waters. LC 120 is a hydroxy-phosphonoacetic acid with polymers and
copolymers to control scaling. It also has inorganic phosphate and sodium
tolytriazole to prevent corrosion and pitting of all metal surfaces. Application Injected directly into the circulating pipe
upstream from the condenser. Cycles of concentration will vary from 5-20 as a
probable upper limit. For higher limits consult our laboratory. Dosage Feed LC 120 from a chemical
mix tank or directly from the drum by means of a proportioning pump at the
rate of 0.5 pound/1,000 gallons of make-up water. Adjust the dosage to
maintain 5-10 ppm of orthophosphate in the circulating water. A pH of 8-8.5
must be maintained. Ù
|
|
|
Cooling Tower Treatment For Hard Make-up Water LC 121 is specially formulated for large
installations and high hardness water. It is developed for effective,
economical cooling water treatment at hospitals, hotels, large apartment
houses, office buildings and other industrial and institutional cooling
installations. Also recommended for a small installations with high hardness
make-up water. It contains no phosphates, chromate, zinc or other chemicals
that cause pollution problem. Helps control mineral deposits, sludge and
surface pitting and does not stain automobiles or buildings. Application Use a reliable automatic proportioner with
timer for controlled dosage. Follow instructions for calculated bleed of rate
and recommended daily maintenance treatment as suggested by the Field Chemist
personnel. The dosage and treatment program depend on size of installation
and water hardness (ppm) Dosage Initial treatment : add
1 gallon of LC 121 per 2,000 gallons of recirculating water. Maintenance
treatment : 1 gallon per 6,000 gallons of water lost to bleed off. Ù
|
|
|
Wide Band Microbiocide For Cooling Towers LC 122 is an effective wide-band Micro-biocide
designed for use in algae and bacteria control. It does not cause foaming and
is not lost by evaporation from the system. It is a concentrated blend of
organo-sulfur compounds, which should be added only after proper dilution by
slug feeding. Application Use to control algae and bacteria in
re-circulating commercial and industrial water-cooling towers. Prior to its
use, systems must be cleaned to remove algae growth, microbiological slime
and other deposits. Dosage An initial slug additions
of LC 122 per 1,000 gallons of water should be employed every 1-5 days or as
needed. The frequency of addition depends upon the relative amount of
bleed-off and the severity of the microbiological problem. Slug additions
should be made in the sump of the cooling tower. During very hot weather,
greater frequency or higher dosage may be required to increase its
effectiveness. Ù
|
|
|
Cooling Tower Treatment LC 123 is specially formulated for large installations
and high hardness water. It is developed for effective, economical cooling
water treatment at hospitals, hotels, large apartment houses, office
buildings and other industrial and institutional cooling installations. Also
recommended for a small installations with high hardness make-up water. It
contains no phosphates, chromate, zinc or other chemicals that cause
pollution problem. Helps control mineral deposits, sludge and surface pitting
and does not stain automobiles or buildings. Application Use a reliable automatic proportioner with
timer for controlled dosage. Follow instructions for calculated bleed of rate
and recommended daily maintenance treatment as suggested by the Field Chemist
personnel. The dosage and treatment program depend on size of installation
and water hardness (ppm) Dosage Initial treatment:
add 1 gallon of LC 123 per 2,000 gallons of recirculating water. Maintenance
treatment as per size of installation & hardness (consult our Technician) Ù
|
|
|
Chlorine Based Microbiocide For Cooling Towers LC 124 is an effective chlorine based designed for use in algae and bacteria control. It
does not cause foaming. It is a concentrated blend of organo - chloro
compounds which should be added only by slug feeding. Application Use to control algae and bacteria in
re-circulating commercial and industrial water cooling towers. Prior to its
use, it is advisable that systems be cleaned to remove slime and other
deposits. Dosage An initial slug additions
of LC 124 per 2,000 gallons of water should be employed every 1-4 days or as
needed. The frequency of addition depends upon the relative amount of
bleed-off and the severity of the microbiological problem. Slug additions
should be made in the sump of the cooling tower. During very hot weather,
greater frequency or higher dosage may be required to increase its
effectiveness. Ù
|
|
|
Scale, Sludge & Corrosion Control For
Cooling Towers LC 126 condenser water treatment does not use sodium
chromate, zinc or other toxic chemicals in its composition. It eliminates the
serious pollution problems usually associated with the use of such chemicals
for corrosion and scale control in cooling system. It protects medium size
cooling towers against scale, sludge and corrosion. LC 126 contains a special
anti-foulant additive to reduce accumulations of mud and silt in condenser
tubes. Ideal for average towers with 75 to 500 ton capacity. Application Formulated for use in open re-circulating
cooling water systems found in air conditioning and process operations. Apply
manually, directly to the cooling tower basin. Dosage Initial Dosage : Add
1 gallon of LC 126 for every 500 gallons of system capacity. Maintenance Dosage :
Add 1 gallon of LC 126 for every 1,000 gallons of system water lost to bleed
off from the cooling tower system Ù
|
∰ Chiller
Water Treatment ∰
|
Code |
Name & Description |
|
Anti Corrosion Treatment For Chiller LC 140 is a liquid blend of nitrite and other corrosion
preventives which protects not only steel surfaces but also copper and other
metals as well. Application Use in hot or cold closed loop systems to prevent
corrosion Dosage Initial dosage : 2.5 gallons of LC 140 per 1,000 gallons
of water in the system and thereafter sufficient to maintain a level of 600
to 800 ppm (mg/l) of nitrite. Ù
|
|
|
Anti Corrosion & Sludge Treatment
Controller For Chiller LC 141 is a single product treatment designed to
prevent scale deposits and corrosion to ferrous and non-ferrous surfaces in
hot water heating systems and chilled closed loops. It passivates the
surfaces and forms a barrier layer to inhibit corrosion. It is a synergistic
combination of phosphonates, polymers and phosphate. Application Easily fed/injected directly into the system by
means of a chemical By-Pass Feeder. Dosage Initial treatment is 1 gallon per 1,000 gallons of
water in the system. Thereafter add LC 141 to maintain a level of 25-35 ppm
(mg/l) of orthophosphate. Ù
|
|
|
Chiller Treatment LC 143 is specially formulated for use in systems
that are constantly exposed to air, such as vented air to pressurized systems
providing corrosion protection even in systems that are not tight. It reduces
maintenance costs by keeping exchangers, air handling units and zone valves
free of corrosion clogs. It also reduces corrosion insulation and system
damage. LC 143 contains boron nitrate that protects against oxygen and acid
attack, works well in any closed system. Recommended for any hot water boiler
or re-circulating or closed loop system. Application Can be added to a system either manually or with a
pot feeder. If the treatment dosage is less that the capacity of feeder, fill
up the feeder with tap water to prevent air on treatment. NOT TO BE USED IN
ELECTRIC STEAM BOILERS. Dosage For chilled water re-circulating system : For
initial or maintenance treatment, add 1 gallon of LC 143 for each 200 gallons
of chilled water. The treatment level is easily tested with the drop
titration nitrite test kit. Ù
|
|
|
Anti Corrosion Treatment For Chiller With Anti
Freeze LC 144 is a glycol based formulation blended with
inhibitors designed to protect all hot & chilled closed loop systems like
chillers, radiators and engines, including aluminum, brass, copper etc.
against rust and corrosion. It contains no methanol and thus has low
flammability, is biodegradable and does not present a problem to the
environment. Application This product should be left in the system all year
round. Dosage Initial dosage : 2.5 gallons of LC 144 per 1,000
gallons of water in the system and thereafter sufficient to maintain a level
of 600 to 800 ppm( mg/l ) of nitrite. Ù
|
∰ Cleaners ∰
|
Code |
Name & Description |
|
Alumunium Cleaner ( Acid Based ) LC 200A is an environment safe, biodegradable, phosphate based
aluminum cleaner and brightener. It is designed not only to dissolve oxide layers,
and has the added benefit of being safer to keep aluminum surfaces looking at
their best. It penetrates and clings to coils for maximum effectiveness. Application Use LC 200A for initial cleaning and brightening on tough or built-up
soil problem. For on-going maintenance use LC 301 for a protective and shiny
coat. For maximum cleaning, apply LC 200A with a high-pressure washer Dosage The dilution will vary, depending on the condition on the surface to
be cleaned. For best result, rinse with a high-pressure washer or apply with
a brush. For normal cleaning & brightening; apply LC 200A up to a
dilution of 1:20 with water. Allow the solution to react with the surface for
3 – 15 minutes, and then rinse thoroughly with clean water through a pressure
washer. Do not allow LC 200A to dry on the surface, and hence LC 200A should
be reapplied if necessary. Ù
|
|
|
Alumunium Cleaner ( Alkaline Based ) LC 200B is an environment safe, biodegradable, non-acid aluminum cleaner
and brightener. It is designed not only to dissolve oxide layers, but also
has the added benefit of being safer to keep alumunium surfaces looking their
best. The non-acid formulation won’t harm sprayers and treatment for severe
coil cleaning problems. It penetrates and clings to coils for maximum
effectiveness. Application Use LC 200B for initial cleaning and brightening on tough or built-up
soil problem. For on-going maintenance use LC 301 for a protective and shiny
coat. For maximum cleaning, apply LC 200B with a high pressure washer Dosage The
dilution will vary, depending on the condition on the surface to be cleaned.
For best result, rinse with a high pressure washer or apply with a brush. For
normal cleaning & brightening ; apply LC 200B at a dilution of 1:25 with
water. Allow the solution to react with the surface for 3 minutes, then rinse
thoroughly with clean water through a pressure washer. Do not allow LC 200B
to dry on the surface. Ù
|
|
|
Industrial Cleaner Concentrate LC
202 is a water based general purpose heavy duty cleaner designed to
penetrate, emulsify and disperse oil, grease, dirt and grime and other types
of soils from a variety of hard surfaces. Ideal for cleaning walls, floors,
desks, light fixtures, automobiles, painted woodwork. Also can be used on
metal surfaces such as stainless steel, aluminum, cooper and brass providing
an excellent cleaning action. Application Spray,
mop, brush wipe, dip method are recommended. Use for cleaning walls, floors,
desks, light fixtures, automobile, painted wood work. Dosage Dilute
with ratio of 1 : 15 (min) up to 1 : 200 with water depending on the dirt
thickness & type of the surfaces. Ù
|
|
|
Glass Cleaner Concentrate LC
203 is an advanced, non-abrasive & concentrated formulation. It is
designed to be used ONLY AFTER DILUTION. The diluted product instantly cuts
thorough grime to leave glass sparkling clean, smear-free and adding a soft
fragrance into the surrounding air. The super strength formula effortlessly
lifts ingrained grime and tobacco haze from interior windows. LC
203 removes grease, finger mark and forms protective film and imparts a
lovely warm radiance, smooth feel on your glass. The anti static component repels tiny dust particles and thus
reduces deposits efficiently. USE LifeChem’s LC 219 ; Glass Polisher to
remove glass stains & deposits. Application 1.
Dilute product with clean, softened water with a ratio
of 2:1 or 1:1 2.
Spray it on the glass, mirror surface 3.
Wipe-off using a glass-wiper in the usual method. 4.
Leave it to dry 5.
Repeat if necessary for highly soiled stains Dosage Should
not be used undiluted and must be diluted to suit method of application
and extent of contamination. Suggested dilution is 2:1 or 1:1. USE CLEAN
& SOFTENED WATER ONLY. Ù
|
|
|
Phosphatic Cleaner Concentrate LC 204 is a specially formulated concentrated acid cleaner which effectively
removes the rust, scale, foulants, dirt and corrosion products on metal
surfaces. The key ingredients are an important metal corrosion inhibitor and
a surfactant. The product incorporates a phosphating agent that serves as a
coating to prevent further corrosion of the metal. Application May be
applied by brushing or spraying. It may be used in its concentrated or
diluted forms. Following the brushing or spraying, the surface of the metal
is rinsed with water upon completion of the reaction which usually takes 5 to
10 minutes. It is recommendable to rinse treated parts with plenty of water
and to use soap or other alkaline material to make sure that it is
neutralized properly. Dosage In the case
of dilution LC 204 is normally diluted with water from 1:5 to 1:20, depending
on the amount of contamination to be removed. Ù
|
|
|
AHU Power Cleaner LC 205 is a powerful blend of detergents,
surfactants, acid emulsifier specifically designed for the cleaning and regular
maintenance of cooling coils of AHU, chiller units in hotels, hospitals,
office buildings etc. Effective to removes grease, oil, dirt, light scale and
other deposits on the cooling coils and fins without affecting the metal
parts. It is not harmful to aluminum coils & fins. Application Use only after proper dilution. Applied by spraying,
brushing or by dipping. Spray method is preferred for in-place cleaning &
dismantling the equipment. Sprayed directly on the soiled parts using hand or
pressure spray system. During cleaning operation, it is to be applied until
all soiled areas are covered & wet. Following a few minutes of reaction
time, it is hosed off with water and allowed to dry. For best result use high
pressure water jet for flushing. A very low concentration ( 0.5% – 1.0% )
solution may directly be used for flushing in the normal way of cleaning. Dosage Should be diluted with water. Dilution ratio up to 1
: 20 ( 1 part of LC 205 can be diluted with 20 parts of water ) Ù
|
∰ Descalers ∰
|
Code |
Name & Description |
|
Descaler Concentrate LC 230 is a strong descaler with a special blend of
acids, corrosion inhibitors, emulsifiers & dispersing agents. It effectively
removes rust, oxides of metals, scale and soil from metal and concrete
surfaces. It is dissolving action on rust, silica and scale is quick and
thorough. Its acid formulation dissolves lime, scale and rust right down to
the base metal or concrete with the selective inhibitor protecting metal
surfaces. Not for materials like glazed tiles and glass. Application Brush or spray on surfaces. Clean surface free from
excess rust, soil and dirt. Apply LC 230. Allow to stand for 10-20 minutes,
then wipe off with water. Surface may require repainting if necessary. Dosage For descaling purposes, dilute one part LC 230 with
up to 10-15 parts of water depending on the thickness scales. Allow to stand
for several hours. Flush with water until all the scale is removed. Repeat if
scale is still present, check pH during application for control. Contact
Field Chemist for further information. Ù
|
|
|
Inhibited Carbonate Descaler Application
LC 231 is a special blend of volatile acids, corrosion inhibitors &
dispersing agents. It effectively removes scale and soil of carbonate nature
from metal and other surfaces. LC 231 is an excellent additive for the LC 230
or LC 233 for the initial removal of the carbonate based scale and
effectively bring down cost by reducing the amount of other descalers.
Its acid formulation dissolves lime scale and rust deep down with the
selective inhibitors protecting metal surfaces. Application Spray
or brush on surfaces. Clean surface free from rust, soil and dirt. Apply LC
231. Allow to stand for 2-5 minutes, scrub thoroughly and re-apply. Repeat
and then flush off with water. Flush with water until all scale is removed.
Add with other descaler like LC 232 & LC 233 for stubborn and difficult
to remove scales. Cannot be used alone. Dosage Dilute
one part of LC 231 with up to 10 parts of water depending on the thickness of
scales. Ù
|
|
|
Descaler Concentrate For Silica Scale LC
232 is a very strong concentrated descaler, specifically designed to remove
silica based scales and other stubborn scales. It is a special blend of
volatile acids, corrosion inhibitors & dispersing agents. It effectively
removes stubborn silica scale and soil of silicate/phosphate nature from
metal and other surfaces. LC 232 is an excellent additive for the LC 231
& LC 233 for additional effectiveness against silica based scales and
effectively bring down cost by reducing the amount of other descalers. Its
special formulation dissolves scale and rust deep down with the selective
inhibitors protecting metal surfaces. Application Spray
or brush on surfaces. Clean surface free from rust, soil and dirt. Apply LC
232. Allow to stand for 2-5 minutes, scrub thoroughly and re-apply. Repeat
and then flush off with water. Flush with water until all scale is removed.
Add with other descaler like LC 231 & LC 233 for stubborn and difficult
to remove scales. For best results use circulation or dipping method use of
passivating agent like LC 252 or LC 253 is essential. Make test strip before
use. NOT TO BE USED ON GLASS/SILICATE BASED SURFACES. Dosage Dilute
one part of LC 232 with up to 10 parts of water or depending on the thickness
of scales. Ù
|
|
|
Multi Purpose Descaler LC
233 is a special blend of non-volatile acids, corrosion inhibitors,
emulsifiers & dispersing agents. Effectively removes rust, scale and soil
from metal and concrete surfaces. Application May
be sprayed or brushed on surfaces. Clean surface free from rust, soil and
dirt. Apply LC 233. Allow to stand for 10 - 20 minutes, then wipe off with
water. Dry surface can be repainted if desired for longer protection Dosage For
descaling of condensers, dilute one part of LC 233 with upto 10 parts of water
depending on the thickness of scales. Allow to stand for several hours. Flush
with water until all scale are removed from condensers. Ù
|
|
|
Alkaline Descaler LC
234 is designed specially for use in systems where the use of acidic
descalers are not recommended. LC 234 may be re-circulated by means of a high
volume pump for the removal of scale. LC 234 can be used safely on to copper
& brass surfaces besides being very effective in steel system. Application LC
234 may be soaked overnight and re-circulated. When scale is present, the
tubes should first scraped out to remove as much as possible and then flushed
out with a hose. Dosage Circulate
a 10% solution (10 gallons of LC 234 for every 100 gallons of water.) for a
period of four to six hours depending on the scale thickness. Solution may be
heated for effectiveness by steaming. The system should then be drained and
inspected. If more scale remains, repeat the process. When the cleaning
process is complete, flush with clean water and place it back in service. For
storing / stand by system use LC 253 or LC 252. Ù
|
|
|
Descaler For Copper & Brass Surfaces LC
234 is designed specially for use in systems where the use of acidic descalers
are not recommended. LC 234 may be re-circulated by means of a high volume
pump for the removal of scale. LC 234 can be used safely on to copper &
brass surfaces besides being very effective in steel system. Application LC
234 may be soaked overnight and re-circulated. When scale is present, the
tubes should first scraped out to remove as much as possible and then flushed
out with a hose. Dosage Circulate
a 10% solution (10 gallons of LC 234 for every 100 gallons of water.) for a period
of four to six hours depending on the scale thickness. Solution may be heated
for effectiveness by steaming. The system should then be drained and
inspected. If more scale remains, repeat the process. When the cleaning
process is complete, flush with clean water and place it back in service. For
storing / stand by system use LC 253 or LC 252. Ù
|
|
|
Heavy Duty Descaler LC
239 is a very strong descaler for destroying the most difficult scales. It is
a special blend of acids, corrosion inhibitors, emulsifiers & dispersing
agents which effectively removes rust, oxides of metals, scale and soil from
metal and other surfaces. It’s dissolving action on rust, silica and scale is
quick and thorough. Not for materials like glazed tiles and glass. Must
be used after dilution only. Application Dilute
as necessary before dipping, brushing or spraying on surfaces. Clean surface
free from excess rust, soil and dirt. Apply LC 239. Allow to stand for 10-20
minutes, then flush off with water. Surface may require repainting if
necessary. Recommended to use LC 240 for neutralization and LC 252 for
passivating the native surface on ferrous metals. Avoid contact with unwanted
surfaces. Dosage For
descaling purposes, dilute one part LC 239 with up to 10-20 parts of water
depending on the thickness of scales.
Allow to stand / circulate for several hours or as necessary. Flush with
water until all the scale is removed. Repeat if scale is still present, check
pH during application for control. Contact Field Chemist for further
information. Do not use above 2% with
non-chemical pumps for circulation Ù
|
|
|
Neutralizing Agent LC
240 is a highly alkaline concentrated product designed for neutralizing the metal
surfaces that is susceptible to corrosion. LC 240 consists of a blend of
soluble carbonate, hydroxide and corrosion inhibitors. It is designed to
control corrosion and neutralize any acid left from “acid cleaning”
processes. It contains no chromate or heavy metals. It is food grade, user
& machine friendly and environmentally safe. Neutralized mixtures can
safely be disposed into sewers. [ P – Powder / L – Liquid ] Application Can
be added directly into the liquid volume to give a 1% to 5% solution or add
till pH value is between 6 - 8, which then may be used for neutralization
& protection. For offline storing purposes a 0.5% solution may be quite
effective. The surface to be neutralized or get protection must receive a
minimum of 5-10 minute contact time. Dosage Dosage
is calculated depending on the circulating or storing volume and the time of
contact. A diluted solution of 0.5% up to 5% is recommended. Use concentrated
solution for less contact time & higher initial conditions, where as a
0.5% solution may be used for storing. Ensure pH value between 6 – 8 before
disposal. Ù
|
∰ Anti Corrosion Treatments ∰
|
Code |
Name & Description |
|
Anti Rust Coating LC
250 is a water displacing anti corrosion compound used to prevent rust on
metal surfaces with unlimited applications in the fields of marine,
automobile, aviation farming, etc. LC
250 creeps along surfaces and into cracks to lubricate, loosen frozen parts and
displace water. The loosened rust can easily be removed. The displacing
mechanism works by preferential wetting. The attraction, of the preventative
that of water, thus displacing water. Application Apply
LC 250 to metal surfaces either by brushing or dipping. When dipping is used,
allow excess chemical to drip prior to storage. Handling & Precaution Avoid
unnecessary skin contact. Prolonged contact may cause irritation. Ù
|
|
|
Dissolve Rust LC
251 is a special blend of acids, detergents, corrosion inhibitors and
surfactants that is used in all operations where rust should be removed and
avoided to lengthen equipment life, efficiency and improve appearance of
metal equipment, machinery, tanks, valves, pipes, etc. LC
251 reacts with the iron oxides to quickly remove and liquefy rust and
corrosion. Simultaneously, the product reacts chemically with the metal
surface to form a thin, continuous layer of phosphates that passivates the
ferrous metals from flash rusting. This layer also acts as a rough base which
firmly bonds paint with maximum adhesion. Application LC
251 may be applied by spraying, brushing or dipping. Allow the solution come
into contact with rusted or corroded surfaces 5 to 15 minutes. The metal may
be occasionally scrubbed with a brush to hasten the appearance of metallic
luster. Finally rinse with cold water Dosage Dilute
with ratio of 1 : 5 with water depending on the rust thickness Ù
|
|
|
Passivating Agent LC
252 is designed to be used for “passivating” open & closed loop systems
to prevent corrosion. It is a liquid blend of nitrite and other corrosion
preventives which protects not only steel surfaces but also copper and other
metal as well. The high concentration makes it a cost effective nitrite based
passivating agent with the added advantage of being multi-metal compatibility
and thus do not require separation of non-ferrous parts from a system during
passivation. Application Normally
injected into the system that is previously filled with standard industrial
grade water and circulated continuously under required pressure for about 1-2
hours with hourly monitoring of the Nitrite concention. A higher temperature
help to accelerate the passivating process and therefore reduce operation
time. An appropriate temperature suitable to the system and available
resources is choosen between 35 – 950C Dosage Initial
: 1 : 400 is suitable in most cases of passivation processes operating at
optimum temperature between 50 – 700C. Depending on the quality of water used
some adjustment in the amount may be required to maintain the pH of the
solution. An increase in concentration of LC 252 is necessary in badly soiled systems. Additional amount
of LC 252 may be required to be added during the circulation for the
passivation process in order to maintain the required control parameters
while monitoring. Ù
|
|
|
Phosphating Agents LC
253 is a highly alkaline concentrated product designed for neutralizing the
metal surfaces that is acceptable to corrosion. LC 253 is also a highly
alkaline formulation of phosphate, polymeric dispersants and corrosion
inhibitors. It is designed to control corrosion and neutralize any acidic
left over from acid cleaning processes. It contains no chromate or heavy
metals. Application Can
be added directly into the raw water to give a 1% to 5% solution, which then
may be used for neutralization & protection. For offline storing purposes
a 0.5% solution may be quite effective. The surface to be neutralized or get
protection must receive a minimum of 5-10 minute contact time. Dosage Dosage
is calculated depending on the circulating or storing volume and the time of
contact. A diluted solution of 0.5% up to 5% is recommended. Use concentrated
solution for less contact time & higher initial conditions, where as a
0.5% solution may be used for storing. Ù
|
|
|
Rust Guard LC
255 is a versatile and highly effective rust preventative for use on unpainted
metals during outdoor storage or overseas shipping. LC 255 protects metal
with heavy waxy film. It does not require any surface cleaning or preparation
and covers the metal like a paint, but easily removable. LC
255 provides protection for storage of metal, equipment, tools, tanks,
structures, machinery, castings, fittings, valves, doors, frames, fixtures,
jigs, etc. Application LC
255 can be applied by spraying, brushing or dipping. It is recommended to
apply by dipping in a tank with water draining facilities which ensures
maximum coverage, penetration and cost effectiveness. LC 255 absorbs water
and moisture while lubricating plated surfaces and bare metals such as steel,
iron, alumunium, copper, brass and lead. Ù
|
|
|
Rust Killer LC
256 is a concentrated blend of acids, corrosion inhibitors, emulsifiers and
wetting agents that converts rust and metallic oxides into a stable and inert
compound. The stable converted coat serves as a good base for subsequent
re-painting. LC
256 replaces old conventional ways of treating rusty metal surface for
re-coating and is successfully used in storage tanks, workshops, factories,
buildings, ship building, etc. Application LC
256 may be used by spraying or brushing. It may be applied directly following
the removal of loose flaking rust. It is recommended to clean the surfaces
with a wire brush prior to the application of LC 256, to achieve a good
instant surface for better paint adhesion and durability. Wash down with
water. Leave
for 12 – 24 hours after which time the conversion will be complete. Then,
rinse again with water. Ù
|
|
|
Clear Coat ( Anti Corrosion ) LifeChem LC 257 is a solvent based anti-corrosion coating for all types of
hard surfaces including stainless steel, wood, aluminium and brass. LC 257
penetrates into the tiny pores of the surface structure and the minute
crevices helped by the selected penetrants. The highly volatile solvents
evaporates quickly to leave an inert, transparent residue that seals the
pores & cover the surfaces. LC 257
is comprised of volatile HC solvents with anti corrosive penetrants, surface
stabilizers designed to provide excellent anti corrosion action. LC 257 is ideal for providing anti
corrosion coating on corrosion surface prone and products. Ù
|
∰ Degreasers ∰
|
Code |
Name & Description |
|
Degreasing Concentrate LC
270 is a water based general purpose cleaner to penetrate, emulsify and
disperse oil, grease, dirt and grime and other types of soils from a variety of
hard surfaces. Ideal for cleaning walls, floors, desks, light fixtures,
automobiles, painted woodwork. Also can be used on metal surfaces such as
stainless steel, aluminum, cooper and brass. Application Spray,
mop, brush wipe, dip method are recommended. Use for cleaning walls, floors,
desks, light fixtures, automobile, painted wood work. Dosage Dilute
with ratio of 1 : 10 with water depending on the dirt thickness Ù
|
|
|
Power Solvent Degreaser LC
271 is a strong solvent based degreaser and decarboniser for the rapid
removal of oil, grease, paint, adhesives and waxes from metal components and
machinery. The mechanism of cleaning involves a quick penetration of LC 271
to soften polymerized oils associated with the carbon deposit. Then the
deposit is loosened and easily dispersed into the solvent. The powerful
solvents act quickly to break the bond between the deposits and the metal
surface. LC 271 is safe to use on ferrous and non-ferrous metals, concrete
and ceramics. Application Ideal
to use in metal dip tanks, spraying, wiping etc. Item to be descaled,
decarbonised or degreased should be immersed below the surface. Loose soiling
should be removed prior to immersion. After removal allow them to drain for
10 minutes. Then, rinse with low pressure water. Keep container covered for
control evaporation. Ù
|
|
|
Carbon Cleaner LC 272 is a water based
concentrated degreaser to penetrate, emulsify and disperse oil, grease, dirt,
soot, grime and other types of soils from a variety of hard surfaces. Safe for all types of metal surfaces. Specially designed for use
in ovens, grills, chimneys, exit-ways, smoke escapes, air vents & other
such places where thick deposits of oil/grease with soot / carbon is common Ù
|
∰ Natural
Stone Care Treatments
∰
|
Code |
Name & Description |
|
Granite Stain Remover ( For White Porous
Materials ) LC
300 is a designed specifically for stains on granite surfaces arising out of contamination
during production or due to storage. It is very effective for stains on
granite surfaces due to poor quality water, inproper storage & soil
contamination. It is an acid based special blend of selected penetrants,
emulsifiers, dispersant & solvent carriers designed to effectively
penetrate, react, dissolve & remove the stains from the surfaces as well
as deeper into the granite structure without affecting the surface. Application Make
sure that the granite surfaces is free from dust, soil & dirt. Apply LC
300 on the pre-treated surface by brushing to leave a thin uniform film on
the whole surface. Do not leave any surface untreated. Wait until 15-30
minutes or more until the stains start dispersing. Rinse and wipe clean the
whole surface with demin water. For deeper & thicker stains, repeat the
process. May not be suitable for certain types of granite & marble.
Always make a test sample before final application. Ù
|
|
|
Water Repelling Coat LifeChem
LC 301 is a solvent based general purpose coating for all types of hard and
porous surfaces including Granite & Marble. LC 301 penetrates into the
tiny pores of the surface structure and the minute crevices helped by the
selected penetrants. The volatile solvents evaporates quickly to leave an
inner, transparent residue that seals the pores. The surface is shining and
polish-able, washable and ready. LC 301 is comprised of volatile HC solvents
, penetrants, emulsifiers and surfactants designed to provide excellent
penetration and sealing action. LC 301 is ideal for providing an inner coat
on porous materials like granite, marble, tiles and such surfaces including
walls, floors, desks, fixtures, woodwork and even paper & paper based
products. Application Applied
by spray, mop, brush wipe, dip. Leave a thin coating and let it dry. Re-apply
for a thickener coat. Available for coating floors, walls, desks, fixtures,
wood work. Special use for granite, marble and porous tiled surfaces of
various colours and types. If there is excess localised deposition, then
re-apply to remove and even the surface. APPLY QUICKLY TO AVOID ACCUMULATION. Ù
|
|
|
Stain Prevention Treatment System 1 ( For White Granite Types ) LC
302 is a blend of corrosion inhibitor, penetrants & dispersants designed
specifically for the protection of granite surfaces from stains and
corrosion. LC 302 is to be applied directly on the surface to prevent
corrosion and stain due to ferrous & non-ferrous metal contaminants. The
synergistic combinations of the various components gives an effective
treatment. LC 302 is a polymer based products that is biodegradable and does
not pollute the environment. Application LC
302 should be applied by spraying, brushing, wiping or diping directly on to the
granite surface. A method allowing mechanical penetration like a forced jet
is recommended. Ensure a thick film left on the exposed surface.
Effectiveness of LC 302 depends on surface condition and method of
application. If surface is contaminated, repeat application. An even coating
throughout the exposed surface must be ensured. For best result, LC 302
should be applied to the freshly cut & cleared granite surface, after
being removed from the gang-saw machine Handling & Precaution LC
302 is a slightly alkaline product. No respiratory protection is required,
however maintain adequate ventilation. Safe for incidental contact with skin,
but prolonged contact must be avoided. In case of contact, wash with water
immediately. Harmful if swallowed, obtain immediate medical attention. Ù
|
|
|
Stain Prevention Treatment System 2 ( For White Granite Types ) LC
303 is a blend of nitrite and other corrosion preventive components which
selectively acts on metal residue and prevents stains & corrosion on granite
surfaces. LC 303 does not have any corrosion effect on the granite itself. LC
303 is to be used after the granite block is removed from the gang-saw
machine. Application LC
303 may be applied by spraying, brushing, wiping or dipping on to the surface.
A method allowing mechanical penetration like a forced jet is recommended.
Ensure a thick film left on the exposed surface. Effectiveness of LC 303
depends on surface condition and method of application. If surface is
contaminated, repeat application. An even coating throughout the exposed
surface must be ensured. Handling
& Precaution Avoid
contact with mineral acids, ammonium salts. It is a slightly alkaline
product. No respiratory protection is required, however maintain adequate
ventilation. Safe for incidental contact with skin, but prolonged contact
must be avoided. In case of contact, wash with water immediately. Harmful if
swallowed, obtain immediate medical attention. Ù
|
|
|
Stain Prevention Treatment System 3 ( For White Granite Types ) LC
304 is a product for the granite industry to be used during production
immediately after polishing. LC 304 is a blend of dispersant and penetrants
whose synergistic effect is long-lasting and prevent stains and corrosion on
granite surfaces. LC 304 is applied to the granite surface after polishing. Application LC
304 should be applied by spraying, brushing or wiping directly on to the
cleaned surface preferably dry. If application is to be made on a wet surface
then it should be wiped off from any residual fluid and dirt. Leave a film of
LC 304 on the surface to dry. Do not leave excess of LC 304 on particular
spots. Effectiveness depend on surface condition and penetration. If surface
is contaminated, repeat application. Handling & Precaution No
respiratory protection is required, however maintain adequate ventilation.
Safe for incidental contact with skin, but prolonged contact must be avoided.
In case of contact, wash with water immediately. Harmful if swallowed, obtain
immediate medical attention. Ù
|
|
|
Water Repelling Coat LC 307 is a solvent based special purpose coating for all types of hard and
porous surfaces including Granite & Marble. LC 307 penetrates into the tiny pores of the surface structure and
the minute crevaces helped by the selected penetrants. The volatile solvents
evaporates quickly to leave an inert, transparent residue that seals the
pores. The surface is shining, washable and ready. Ù
|
∰ Customized Products ∰
The following are the
few customized products from the R & D Section. At the time of this company
profile being published, we are having 6 customized products and 10 more
products, which are still under our Research & Development in the LifeChem
Laboratory. The details, which cannot be mentioned here to keep the
exclusiveness of our customers.
|
Code |
Name & Description |
|
/LC 220 |
Dip-tank Carbon Remover LC
500 is a two layer cold tank degreaser and decarboniser for the rapid removal
of oil, grease, paint, adhesives and waxes from metal components and
machinery. The product is designed specifically for dip tank usage. The
mechanism of cleaning involves a quick penetration of LC 500 to soften
polymerization oils associated with the carbon deposit. Then the deposit is
loosened and easily dispersed into the solvent phase of the product. The
upper layer serves as a sealant to prevent unnecessary evaporation of active
organic solvent and also acts as a solvent rinse. The powerful solvents act
quickly without heating to break the bond between deposits and metal. LC
500 is safe tousle on ferrous and non-ferrous metals, concrete and ceramics. Application Designed
for use in metal dip tanks only. Items to be degreased should be placed below
the interface of the two layers. Loose soiling should be removed prior to
immersion. After removal allow them to drain for 10 minutes. Then, rinse with
low pressure water. Handling & Precaution Harmful
if inhaled. May cause burns to eyes and skin. In case of contact with skin,
wash immediately with plenty of water. Ensure adequate ventilation at point
of use. If swallowed, seek medical advice immediately. Ù
|
|
/LC 221 |
Carbon Remover Solvent LC
501 is a strong solvent based degreaser and decarboniser for the rapid
removal of oil, grease, paint, adhesives and waxes from metal components and
machinery. The mechanism of cleaning involves a quick penetration of LC 501
to soften polymerized oils associated with the carbon deposit. Then the
deposit is loosened and easily dispersed into the solvent. The powerful
solvents act quickly to break the bond between the deposits and the metal
surface. LC 501 is safe to use on ferrous and non-ferrous metals, concrete
and ceramics. Application Ideal
to use in metal dip tanks, spraying, wiping etc. Item to be descaled,
decarbonised or degreased should be immersed below the surface. Loose soiling
should be removed prior to immersion. After removal allow them to drain for
10 minutes. Then, rinse with low pressure water. Keep container covered for
control evaporation. Handling & Precaution Harmful
if inhaled. May cause burns to eyes and skin. In case of contact with skin,
wash immediately with plenty of water. Ensure adequate ventilation at the
point of use. If swallowed, seek medical attention. Ù
|
And many more…
More than 100 products which
we are producing and hundreds more which we are developing, has become our
strength to see the future in the business. This accommodate our commitment to
our customers that:
“Customer Satisfaction is the Key to Success”
Contact us by E-mail: LifeChem
ÙTOP
Our
LifeChem Web is a Next Generation Technology in Chemical Maintenance that puts
you in control of your maintenance needs! FREE Information, Free use, get
it right now by clicking
right here! Our other users can't be wrong.